Homebuilt Experimental Aircraft

About the kit aircraft:

Where are aircraft builders located?

View a map of all aircraft projects

Aircraft Builders Building Aircraft

2 airplane projects found for

Cleveland, GA
glennm Stayner, ON

Most Recent Aircraft Photos From All Builders

Escapade homebuilt experimental aircraft project Center

Escapade Center Fuselage
(Uploaded Feb 27, 2007 by glennm)

Escapade homebuilt experimental aircraft project Flight

Escapade Flight Controls
(Uploaded Feb 27, 2007 by glennm)

Escapade homebuilt experimental aircraft project Main

Escapade Main Gear
(Uploaded Feb 23, 2007 by glennm)

Escapade homebuilt experimental aircraft project Nosewheel

Escapade Nosewheel
(Uploaded Feb 23, 2007 by glennm)

Latest Log Entries for Escapade

May 17, 2012 - Van's Aircraft, Inc RV-7: Empennage Tip Fairings Lay-up and Filler Fairing: Removed plug from intial fiberglas lay-up in tip fairings. Added second layer of glass and some filler (glass balls) with resin to fill void... more »
May 17, 2012 - Sonex Aircraft, LTD Waiex: Fuel tank calibration Miscellaneous: Spent the evening calibrating the fuel tank display in the Stratomaster Ultra Horizon XL EFIS unit. I have decided to calibrate it wit... more »
May 16, 2012 - Sonex Aircraft, LTD Waiex: Oil system work - tacking down a leak and other misc stuff Engine: After looking around to figure out where the oil leak was coming - I thought it was from the oil pressure transducer in the block - I decided ... more »
May 17, 2012 - Zenair CH801: Deburring Elevators: Finished deburring rear skin and deburred outward surfaces of the bottom of the elevator skeleton....... more »
May 17, 2012 - Zenair Zodiac HDS: Battery mount Miscellaneous: Riveted the bottom of the battery holder to the skin. Added left over baffle material under and behind the battery.

Ma... more »
May 12, 2012 - Sonex Sonex: Finished both Rear Wing Spars Rear Spar: De-burred, cleaned with scotch bright and metho both Rear Wing Spars. Primed riveting areas with self priming aluminium primer. Assembled a... more »
May 11, 2012 - Sonex Sonex: Up-drilled L H Rear Spar Assembly Rear Spar: Finished assembly W12. Up-drilled to rivet size and bolted AN3-7a bolds for the Root Rib Attach Angle. Disassembly and start de-burring...... more »
May 10, 2012 - Sonex Sonex: Drawing W12 Rear Spar: Cut and filed out Control clearance holes in W12-02 R H and L H Rear Spar Channels. Cut to length, marked and drilled pilot holes using a t... more »
May 09, 2012 - Sonex Sonex: Finished drawing W13 Rear Spar: Modified W13-01 to W13-01R R H Attach Plate what is slightly different than W13-01L L H Attach Plate. Up-drilled on both plates one hole to... more »
May 08, 2012 - Sonex Sonex: Start drawing W13 Rear Spars Rear Spar: Made two W13-04 Dubbler and start W12-01R Atttach Plate....... more »
May 07, 2012 - Sonex Sonex: Finished mating Main Wing Spar Main Spar: Continue mating both Spars. Filed about 1mm off both Lower inner Spar areas to clear the interference with End Wing Attach Assembly bolds. ... more »
May 04, 2012 - Sonex Sonex: Meting R H and L H Main Wing Spars Main Spar: During meting the R H and L H Main Wing Spar together one bold on both End Wing Attach Assemblies are interfering, I took these 2 bolds out... more »
May 03, 2012 - Sonex Sonex: Finished L H Main Wing Spar Main Spar: Fitted the Root Ribs Attach Angles W20-02 and 03. Rounded the washers for the AN3 bolds underneath the nuts to prevent damage to the radius... more »
May 02, 2012 - Sonex Sonex: Finished riveting L H Main Wing Spar Main Spar: Did the rest of the riveting using the 16mm stainless steel rod. None of the rivets done today needed to be redone.
Finished solid r... more »
May 01, 2012 - Sonex Sonex: Solid riveting L H Main Wing Spar Main Spar: Start solid riveting, did the flash riveting first. I used as much I could the 16mm stainless steel rod. This works very well. On the root ... more »
May 16, 2012 - Van's Aircraft, Inc RV-7: Fairing Fiberglas Work Fairing: Worked on the empennage tip fairings. To be kind lets just say I hate doing fibergals work. I began by attaching the elevators to the H.S. ... more »
May 17, 2012 - Vans RV-9A: Stiffeners Fuel Tanks: I had an hour or so and made it out to the garage to cut and fit the stiffeners. It was pretty straightforward since now my understanding ... more »
May 15, 2012 - Rans S-19: Worked on canopy Canopy: The canopy is not an easy task. Lots of testing and fitting to get all the holes to line up. I have made some changes from the kit instruction... more »
May 15, 2012 - Van's Aircraft, Inc RV-7: Air Vent NACA Scoops Miscellaneous: Cut out 4 strips of aluminum to use as backing for the SV-1 NACA Scoops. Layed out a line and came up with 6 rivets evenly spaced on b... more »
May 14, 2012 - Zenith Aircraft CH750: Built LAV's Two Flaps Flaps: Riveted bottoms. LVE took flaperons (flaps and ailerons) home where he will finish attaching attach fittings and ready for pre-close inspection... more »
May 15, 2012 - Zenith Aircraft CH601XL: Rear fuselage assembly Rear Fuselage: ...... more »
May 15, 2012 - Vans RV6: Wings came pre-built Parts Preparation: The original builder had the wing parts sent to a professional build shop in Oregon and took delivery of the assembled wings. They... more »
May 15, 2012 - Vans RV6: Priming - what to do... Primer: I'm at a little bit of a quandry on the priming needed. The wing kit is came complely primed inside and outside and is ready for assembly. T... more »
May 15, 2012 - Vans RV6: Parts as aquired Rudder: The kit I bought had the empanage partially constructed and primed. I just need to go back through the blueprints and assembly instructions a... more »
May 15, 2012 - Vans RV6: Parts as aquired Vertical Stabilizer: The kit I bought had the empanage partially constructed and primed. I just need to go back through the blueprints and assembly i... more »